CP3 vs CP4 injection pump. These are the differences

Every fuel injection system in an automotive engine operates on the same general principle. It delivers fuel at the right time and pressure to the combustion chamber, mixing it with air and igniting it, creating the explosion that powers your vehicle down the road.

If you’re adding aftermarket performance parts, however, you may wonder which injection pump is better: CP3 or CP4? Here’s how they differ, and which one you should choose for your project.

Most Significant Differences Between CP3 vs CP4 Injection Pump

Even though the functions of these two pumps are almost similar, there are still some significant differences between them. The most obvious difference is that CP4 pumps have a higher pressure rating than CP3 pumps.

This increased pressure rating means that the pump can handle more work before it starts to wear out or break down. It can also withstand higher temperatures, so you don’t have to worry about overheating issues with your machine or damage from overheating issues.

What is a CP3 Injection Pump

The CP3 injection pump is a high-pressure fuel injection pump designed to deliver fuel to the combustion chamber of an internal combustion engine.

The CP3 pumps can be used in a variety of applications, including diesel engines, gasoline engines, automotive engines, and marine engines.

The CP3 pumps have an extended range over their competitors because they use an integrated centrifugal force clutch for maximum efficiency and reliability in all conditions, including high temperatures and low air pressures.

This feature also allows them to be mounted inside the engine block where other pumps do not fit well or cannot be used at all due to their size requirements or interference with other components such as spark plugs or throttle cables.

What is a CP4 Injection Pump

The CP4 injection pump is a common solution to the problem of how to get fuel into the engine. It is a type of mechanical fuel pump that uses a belt to transfer power from an engine to the pump.

The CP4 injection pump is made up of two parts: the drive plate and the return plate. These plates are attached to each other by way of an arm that allows them to move back and forth.

When an engine’s piston moves forward, this arm allows these plates to move inwards towards each other which increases pressure in the system and forces fuel through small holes located on both sides of the plates.

The pressure inside the system determines how much fuel can be pumped at once. This pressure can be controlled by moving the plates closer together or farther apart, increasing or decreasing their distance from one another.

The amount of force required for this movement is determined by how much pressure has been built up within the system since the last time it was operated.

Advantages of CP3 Injection Pump

High Performance and High Reliability:

The pump is designed from the ground up to deliver maximum performance with minimum maintenance. It is designed with a fully variable speed motor that allows you to adjust the speed to match your needs.

The pump has an oil return valve to reduce wear on your car’s engine and transmission. The pump also has a pressure relief valve that helps to prevent over-pressurization of the system, which could damage components or cause a fire in the engine bay.

Easy Installation

The pump is easy to install and can be mounted on almost any vehicle with ease, including SUVs, trucks, vans, and cars. It comes with all the necessary hardware and instructions for an easy installation process.

Fuel Economy

Because it supplies fuel to the engine at a controlled rate, you will get better mileage out of your vehicle.

Less Maintenance

Because there is a constant flow of fuel into the engine, you will not have to do as much maintenance on it as other engines which use an external source.

Disadvantages of the CP3 pump

Advantages of CP4 Injection Pump

The advantages of the cp4 injection pump are as follows:

  1. The most important advantage is that it can easily be installed, operated, and maintained because it is a direct-injection pump. The only thing you have to do is replace the old one with a new one.
  2. It has a high-efficiency rate and low noise level, which makes it more environmentally friendly than other types of pumps.
  3. Its output pressure can be adjusted according to the demand of work so that it can meet various requirements from different industries and users.
  4. It has good sealing performance and long service life so its maintenance cost is relatively low compared with other kinds of pumps (such as centrifugal pumps).

Disadvantages of the CP4 pump

  1. The pump is not easy to be repaired by yourself
  2. The pump needs to be adjusted frequently

Similarities Between CP3 vs CP4 injection pumps

There are some similarities between the two types of injection pumps. Both the CP3 and CP4 pumps have an oscillating impeller, which is a rotating element that improves the flow rate and pressure.

They also have a keyway, which is an opening in the side of the pump housing that allows for internal components to be accessed.

The CP3 and CP4 pumps have different heads and shafts as well as different stroke lengths and sizes. The size of these components determines how much pressure can be produced by each unit.

What is Recommended to Choose Between Them and Why?

When it comes to performance, a CP3 injection pump has the ability to handle more horsepower than the CP4. The CP3 is recommended if you are looking for more horsepower and can accommodate higher pressures. However, if you do not plan on running at high pressures, then the CP4 injection pump is more suitable.


After learning about the benefits and drawbacks of each type of injection pump, it’s up to you to decide which is better for your needs. If you’re looking for more power and performance, go with a CP3 pump.

If you want improved fuel economy and lower emissions, choose a CP4 pump. Ultimately, the best injection pump for you is the one that will help you meet your specific goals.

Scroll to Top